MORryde TV40-002H Horizontal Sliding TV Mount - Verify Revision, 45 lb Manual Limit
Ready to order
MORryde TV40-002H Horizontal Sliding TV Mount - Verify Revision, 45 lb Manual Limit
---
MORryde TV40-002H is a horizontal sliding TV mount for baggage-compartment viewing, with a pivoting TV plate and a pull-handle lock. Current and retained older instructions specify a 45 lb maximum. Confirm the actual revision rather than relying on the earlier 50 lb and 36-inch claims.
This horizontal slide moves the TV out of a baggage compartment and lets its plate pivot for viewing. Version 3 says up to 35 inches of extension and 180° pivot; the older retained manual says up to 120° swivel, and the archived catalog lists 22-inch extension/120° pivot. The current manufacturer page itself mixes 180° and 120°. These source values are not a verified single range for every revision. The earlier 36-inch claim is not supported by the reviewed manufacturer sources. Measure the actual assembly, screen swing and cable slack before ordering or installation.
Compare the MORryde RV TV-mount collection when you need to review horizontal sliding, ceiling, snap-in, swivel, and docking-style options side by side.
Original product note: Horizontal Sliding TV Mount The versatile design of this horizontal sliding TV mount gives you options to adjust the depth to easily slide past door frames or other obstacles. A locking mechanism holds your TV or monitor securely in place during travel. Watch TV inside or out with this horizontal sliding TV mount for your RV. Easily clear a door handle or frame by adjusting the depth of the slide from the wall. For ideal viewing, simply slide out your TV or monitor and pivot it into position. Features 200 x 200 VES…
Features & Specifications
- Horizontal slide and pivoting TV plate; verify revision-specific motion limits
- 45 lb maximum per current page and reviewed manuals; archived 50 lb claim conflicts
- Up to 3-inch bracket depth adjustment for cargo-lip clearance; verify actual setup
- Pull handle releases lock; stow and verify lock engagement before travel
Why Choose TV40-002H?
Choose this horizontal slide only after matching the actual mount revision, TV, reinforced vertical attachment and cargo-bay clearance. MORryde’s current TV40-002H page and Version 3 instructions specify a 45 lb maximum TV weight; the older instructions retained here also specify 45 lb. The archived catalog and earlier listing say 50 lb, which conflicts with those instructions. Use the actual mount’s label and applicable instructions; do not assume a 50 lb rating. The gallery label also shows 45 lb. Actual supplied revision remains unconfirmed.
Fitment limit: match this item to your existing MORryde part number, RV measurement, frame/rating, door width, VESA pattern, or MORryde documentation. If the verified details do not match your RV, choose the correct sibling or alternative instead of forcing this part.
Compare MORryde RV TV Mounts
Not sure which MORryde option is right? Compare this product with nearby ERVP listings and verify the part number before ordering.
| Model / Part | Category | Best For | View Details |
|---|---|---|---|
| TV40-002H horizontal sliding TV mount — verify revision and 45 lb manual limit | RV TV Mounts | mounting or securing an RV TV after matching VESA pattern, weight rating, and mount style | Current Product |
| TV1-051H Snap-In TV Mount - 25 lb. capacity - TV1-051H |
RV TV Mounts | mounting or securing an RV TV after matching VESA pattern, weight rating, and mount style | View Details |
| TV1-048H Snap-In TV Mount - 35 lb. capacity - TV1-048H |
RV TV Mounts | mounting or securing an RV TV after matching VESA pattern, weight rating, and mount style | View Details |
| TV10-S-35H Snap-In TV Mount - 35 lb. capacity - TV10-S-35H |
RV TV Mounts | mounting or securing an RV TV after matching VESA pattern, weight rating, and mount style | View Details |
Tip: MORryde part numbers are specific. Check the SKU and the physical measurement, rating, side, generation, or application on your RV before choosing between similar listings.
Technical Specifications
| Brand | MORryde |
| SKU | TV40-002H |
| Part Number | TV40-002H |
| Product Family | MORryde RV TV Mounts |
| Capacity | 45 lb per current page and reviewed manuals; archived 50 lb conflicts—verify label/revision |
| Shipping Weight | 82.8072 lb |
| Product Type | RV TV Mounts |
What's Included
The manual lists the wall bracket, mounting plate and hardware pack. Version 3 illustrates M4/M5/M6 × 12 mm TV bolts, washers and 1/4-inch × 1-inch lag bolts; the older manual additionally illustrates longer TV bolts, M8 bolts, optional spacers, lock washers and self-drilling screws. The actual pack/revision is unconfirmed, and some TVs need separately obtained hardware. Use the TV’s required thread/depth and suitable structural fasteners; the instructions specify a 1/8-inch pilot for 1/4-inch lag bolts. Fasteners that are too long can puncture exterior structure. The TV can be bolted to the plate without removing it; two people may be needed. MORryde’s page describes up to 3 inches of depth adjustment to clear door frames or handles; the archived catalog diagrams brackets extending an extra 3 inches to clear the cargo-bay lip. This is bracket stand-off adjustment, not an extra 3 inches to add to slide travel. The reviewed manuals do not establish a separate add-on bracket kit or service part number. Confirm the brackets supplied with the actual revision and available clearance.
Compatible Models & Alternatives
The comparison links identify different complete mount designs; they do not establish interchangeable parts. Version 3 lists 75×75, 100×100, 100×200 and 200×200 mm VESA patterns. Match both hole spacing and the TV’s required screw thread and permitted depth. The older manual mentions a separately available 200×400 mm adapter through MORryde, but supplies no exact adapter part number. A generic adapter recommendation or shared brand does not confirm compatibility with a specific catalog adapter or TV model.
Frequently Asked Questions
- How do I confirm this is the right MORryde part?
- MORryde’s current TV40-002H page and Version 3 instructions specify a 45 lb maximum TV weight; the older instructions retained here also specify 45 lb. The archived catalog and earlier listing say 50 lb, which conflicts with those instructions. Use the actual mount’s label and applicable instructions; do not assume a 50 lb rating. The gallery label also shows 45 lb. Actual supplied revision remains unconfirmed. Version 3 lists 75×75, 100×100, 100×200 and 200×200 mm VESA patterns. Match both hole spacing and the TV’s required screw thread and permitted depth. The older manual mentions a separately available 200×400 mm adapter through MORryde, but supplies no exact adapter part number. A generic adapter recommendation or shared brand does not confirm compatibility with a specific catalog adapter or TV model.
- What should I measure before ordering?
- The current manufacturer page gives overall 13 inches H × 24 inches W × 6.5–9.5 inches D; the archived catalog gives 24.25 inches W × 13 inches H × 6.5 inches D. Width and depth descriptions differ. Measure the actual bracket footprint, stand-off, stowed and extended assembly, screen, obstacles and cables. These figures do not certify packed dimensions, a universal clearance envelope or the retained native weight/operational measurements. The installation steps and older manual specify mounting to a vertical surface/wall. Version 3’s introductory under-cabinet/ceiling wording and the website ceiling tip conflict with that direction, so ceiling or horizontal-surface installation is not confirmed by this review. The support must carry five times the combined TV-and-mount weight and may need reinforcement. The manuals exclude brick, concrete and concrete block. Verify the actual structural attachment, fastener engagement and full moving clearance.
- Can I substitute a similar MORryde product?
- Only use parts or another mount when exact revision, structural requirements, interfaces and ratings are confirmed. MORryde’s page describes up to 3 inches of depth adjustment to clear door frames or handles; the archived catalog diagrams brackets extending an extra 3 inches to clear the cargo-bay lip. This is bracket stand-off adjustment, not an extra 3 inches to add to slide travel. The reviewed manuals do not establish a separate add-on bracket kit or service part number. Confirm the brackets supplied with the actual revision and available clearance.
- What do buyers usually pair with this part?
- The reviewed sources do not establish a specific catalog adapter, TV model or service-part match. Version 3 lists 75×75, 100×100, 100×200 and 200×200 mm VESA patterns. Match both hole spacing and the TV’s required screw thread and permitted depth. The older manual mentions a separately available 200×400 mm adapter through MORryde, but supplies no exact adapter part number. A generic adapter recommendation or shared brand does not confirm compatibility with a specific catalog adapter or TV model.
Why Buy from Elkhart RV Parts?
Elkhart RV Parts focuses on hard-to-find RV service parts with clear part-number identification, practical fitment notes, and fast support from a team located in Elkhart, Indiana.
Capacity and conflicting sources
MORryde’s current TV40-002H page and Version 3 instructions specify a 45 lb maximum TV weight; the older instructions retained here also specify 45 lb. The archived catalog and earlier listing say 50 lb, which conflicts with those instructions. Use the actual mount’s label and applicable instructions; do not assume a 50 lb rating. The gallery label also shows 45 lb. Actual supplied revision remains unconfirmed.
Sliding, pivoting and bracket clearance
This horizontal slide moves the TV out of a baggage compartment and lets its plate pivot for viewing. Version 3 says up to 35 inches of extension and 180° pivot; the older retained manual says up to 120° swivel, and the archived catalog lists 22-inch extension/120° pivot. The current manufacturer page itself mixes 180° and 120°. These source values are not a verified single range for every revision. The earlier 36-inch claim is not supported by the reviewed manufacturer sources. Measure the actual assembly, screen swing and cable slack before ordering or installation.
Cargo-lip bracket adjustment
MORryde’s page describes up to 3 inches of depth adjustment to clear door frames or handles; the archived catalog diagrams brackets extending an extra 3 inches to clear the cargo-bay lip. This is bracket stand-off adjustment, not an extra 3 inches to add to slide travel. The reviewed manuals do not establish a separate add-on bracket kit or service part number. Confirm the brackets supplied with the actual revision and available clearance.
Mounting surface and support
The installation steps and older manual specify mounting to a vertical surface/wall. Version 3’s introductory under-cabinet/ceiling wording and the website ceiling tip conflict with that direction, so ceiling or horizontal-surface installation is not confirmed by this review. The support must carry five times the combined TV-and-mount weight and may need reinforcement. The manuals exclude brick, concrete and concrete block. Verify the actual structural attachment, fastener engagement and full moving clearance.
Travel lock and outdoor viewing
The diagrams label the handle: pull it to release the lock, extend and swivel. The older manual explicitly prohibits travel with the mount extended; the manufacturer page describes a spring-loaded travel lock. Return the mount to its stored position and verify the lock is engaged before movement, following the actual revision’s instructions. A replacement latch/handle service part number and a universal extra-restraint procedure were not established. Outdoor viewing does not certify weather resistance or permanent exterior storage.
Dimensions and clearance
The current manufacturer page gives overall 13 inches H × 24 inches W × 6.5–9.5 inches D; the archived catalog gives 24.25 inches W × 13 inches H × 6.5 inches D. Width and depth descriptions differ. Measure the actual bracket footprint, stand-off, stowed and extended assembly, screen, obstacles and cables. These figures do not certify packed dimensions, a universal clearance envelope or the retained native weight/operational measurements.
Installation instructions and source limits
Current TV40-002H Version 3 instructions · Retained older TV40-002H instructions · Archived MORryde catalog, page 23
| Width (inches) | 24 |
|---|---|
| Height (inches) | 13 |
| Depth range (inches) | 6.5-9.5 |
| Pivot range (degrees) | Version 3: 180; older manual/catalog: 120; current page conflicts; verify actual revision |
| Product weight (pounds) | 25 |
| Weight capacity (pounds) | 45 per current page and both reviewed manuals; archived 50 conflicts—verify actual label/revision |
| Adjustable depth (inches) | Up to 3 bracket stand-off per manufacturer; not additional slide travel |
| Sliding extension (inches) | Version 3: up to 35; archived catalog: 22; prior 36 unsupported; actual revision/range unconfirmed |
| Vesa mounting pattern (millimeters) | 75x75, 100x100, 100x200, 200x200 per Version 3; verify TV thread/depth |
| Source and dimension limits | The current manufacturer page gives overall 13 inches H × 24 inches W × 6.5–9.5 inches D; the archived catalog gives 24.25 inches W × 13 inches H × 6.5 inches D. Width and depth descriptions differ. Measure the actual bracket footprint, stand-off, stowed and extended assembly, screen, obstacles and cables. These figures do not certify packed dimensions, a universal clearance envelope or the retained native weight/operational measurements. |
| Mount orientation and structure | The installation steps and older manual specify mounting to a vertical surface/wall. Version 3’s introductory under-cabinet/ceiling wording and the website ceiling tip conflict with that direction, so ceiling or horizontal-surface installation is not confirmed by this review. The support must carry five times the combined TV-and-mount weight and may need reinforcement. The manuals exclude brick, concrete and concrete block. Verify the actual structural attachment, fastener engagement and full moving clearance. |
| Hardware and included parts | The manual lists the wall bracket, mounting plate and hardware pack. Version 3 illustrates M4/M5/M6 × 12 mm TV bolts, washers and 1/4-inch × 1-inch lag bolts; the older manual additionally illustrates longer TV bolts, M8 bolts, optional spacers, lock washers and self-drilling screws. The actual pack/revision is unconfirmed, and some TVs need separately obtained hardware. Use the TV’s required thread/depth and suitable structural fasteners; the instructions specify a 1/8-inch pilot for 1/4-inch lag bolts. Fasteners that are too long can puncture exterior structure. The TV can be bolted to the plate without removing it; two people may be needed. |
| Travel lock | The diagrams label the handle: pull it to release the lock, extend and swivel. The older manual explicitly prohibits travel with the mount extended; the manufacturer page describes a spring-loaded travel lock. Return the mount to its stored position and verify the lock is engaged before movement, following the actual revision’s instructions. A replacement latch/handle service part number and a universal extra-restraint procedure were not established. Outdoor viewing does not certify weather resistance or permanent exterior storage. |
| Adapter and tv-model limits | Version 3 lists 75×75, 100×100, 100×200 and 200×200 mm VESA patterns. Match both hole spacing and the TV’s required screw thread and permitted depth. The older manual mentions a separately available 200×400 mm adapter through MORryde, but supplies no exact adapter part number. A generic adapter recommendation or shared brand does not confirm compatibility with a specific catalog adapter or TV model. |
| Native weight scope | Retained Product Weight 25 and separate native measurement fields were not independently certified in this review. |
- What is the weight capacity of the morryde tv40-002h adjustable horizontal sliding tv mount? MORryde’s current TV40-002H page and Version 3 instructions specify a 45 lb maximum TV weight; the older instructions retained here also specify 45 lb. The archived catalog and earlier listing say 50 lb, which conflicts with those instructions. Use the actual mount’s label and applicable instructions; do not assume a 50 lb rating. The gallery label also shows 45 lb. Actual supplied revision remains unconfirmed.
- How far can the tv slide out from the wall with this mount? This horizontal slide moves the TV out of a baggage compartment and lets its plate pivot for viewing. Version 3 says up to 35 inches of extension and 180° pivot; the older retained manual says up to 120° swivel, and the archived catalog lists 22-inch extension/120° pivot. The current manufacturer page itself mixes 180° and 120°. These source values are not a verified single range for every revision. The earlier 36-inch claim is not supported by the reviewed manufacturer sources. Measure the actual assembly, screen swing and cable slack before ordering or installation.
- Does this tv mount allow for swiveling the tv for better viewing angles? This horizontal slide moves the TV out of a baggage compartment and lets its plate pivot for viewing. Version 3 says up to 35 inches of extension and 180° pivot; the older retained manual says up to 120° swivel, and the archived catalog lists 22-inch extension/120° pivot. The current manufacturer page itself mixes 180° and 120°. These source values are not a verified single range for every revision. The earlier 36-inch claim is not supported by the reviewed manufacturer sources. Measure the actual assembly, screen swing and cable slack before ordering or installation.
- What is included in the box when purchasing this tv mount? The manual lists the wall bracket, mounting plate and hardware pack. Version 3 illustrates M4/M5/M6 × 12 mm TV bolts, washers and 1/4-inch × 1-inch lag bolts; the older manual additionally illustrates longer TV bolts, M8 bolts, optional spacers, lock washers and self-drilling screws. The actual pack/revision is unconfirmed, and some TVs need separately obtained hardware. Use the TV’s required thread/depth and suitable structural fasteners; the instructions specify a 1/8-inch pilot for 1/4-inch lag bolts. Fasteners that are too long can puncture exterior structure. The TV can be bolted to the plate without removing it; two people may be needed.
- Can the depth of the mount be adjusted to clear door frames or handles? MORryde’s page describes up to 3 inches of depth adjustment to clear door frames or handles; the archived catalog diagrams brackets extending an extra 3 inches to clear the cargo-bay lip. This is bracket stand-off adjustment, not an extra 3 inches to add to slide travel. The reviewed manuals do not establish a separate add-on bracket kit or service part number. Confirm the brackets supplied with the actual revision and available clearance.
- Which mounting surface, vesa patterns and adapter are verified? The installation steps and older manual specify mounting to a vertical surface/wall. Version 3’s introductory under-cabinet/ceiling wording and the website ceiling tip conflict with that direction, so ceiling or horizontal-surface installation is not confirmed by this review. The support must carry five times the combined TV-and-mount weight and may need reinforcement. The manuals exclude brick, concrete and concrete block. Verify the actual structural attachment, fastener engagement and full moving clearance. Version 3 lists 75×75, 100×100, 100×200 and 200×200 mm VESA patterns. Match both hole spacing and the TV’s required screw thread and permitted depth. The older manual mentions a separately available 200×400 mm adapter through MORryde, but supplies no exact adapter part number. A generic adapter recommendation or shared brand does not confirm compatibility with a specific catalog adapter or TV model.
- How is the mount released and secured for travel? The diagrams label the handle: pull it to release the lock, extend and swivel. The older manual explicitly prohibits travel with the mount extended; the manufacturer page describes a spring-loaded travel lock. Return the mount to its stored position and verify the lock is engaged before movement, following the actual revision’s instructions. A replacement latch/handle service part number and a universal extra-restraint procedure were not established. Outdoor viewing does not certify weather resistance or permanent exterior storage.
Loading customer reviews…
Factory-Fresh OEM Parts — the same brands installed in new RVs straight from Elkhart. Genuine, name-brand components made to order — never generic, never outdated. Sourced directly from the original RV manufacturers for perfect fit and factory-level quality.








