Lippert 8,000-lb Slipper Leaf Spring, 6 Leaves, 3 x 30-1/2 in - 353498
Ready to order
Lippert 8,000-lb Slipper Leaf Spring, 6 Leaves, 3 x 30-1/2 in - 353498
---
Lippert 8,000-lb Slipper Leaf Spring, 6 Leaves, 3 x 30-1/2 in - 353498
Lippert 353498 is a six-leaf steel slipper spring with an 8,000-pound spring-assembly capacity. It has a single-eye design, a listed width of 3 inches and listed length of 30-1/2 inches. The flexible leaves help absorb road shock and vibration to reduce strain on a matching trailer suspension.
This listing supplies one slipper leaf spring with the eye bushing pre-installed. It requires suitable pre-mounted hangers; hanger kits are sold separately. Match the original equipment label and suspension geometry before ordering. The 8,000-pound figure rates this spring assembly and does not independently establish axle capacity, trailer gross weight rating or an approved suspension upgrade.
Why Choose This Slipper Spring?
- Single-eye slipper design: one spring eye and one slipper end for the matching suspension arrangement.
- Six steel leaves: flex to absorb road shock and vibration during trailer use.
- Defined spring rating: 8,000-lb spring-assembly capacity, subject to the original suspension requirements.
- Reference dimensions: 3-inch width and 30.5-inch listed length; verify the source's measurement convention on your original.
- Identification references: Standens 72-46 and Lippert's listed Dexter-compatible number 072-046-00.
- Pre-installed bushing: spring eye bushing included; hanger kits are separate.
- Genuine replacement: Lippert part 353498 with a limited one-year warranty under the manufacturer's terms.
Technical Specifications
- SKU: 353498
- Brand: Lippert
- Weight Capacity: 8,000 lbs.
- Standens Leaf Spring Number: 72-46
- Spring Layer Count: 6
- Eye To Eye Length: 30.5
- Axle Spring Type: Slipper Leaf
- Load Arch Length: 2.75
- Axle Type: Spring
- Hardware Type: Spring
- Unit of Measure: EA
- Item Length (Inches): 30.5
- Item Width (Inches): 3
- Warranty Term: 1 Year
- Quantity In Package: 1
- Package Type: Kraft Box
- Country of Origin: USA
- Dexter Compatible Part Number: 072-046-00
- UPC: 848150068804
- Shipping Dimensions: 41" L x 20" W x 10" H, 55 lbs.
Before You Order
Reference the original equipment label, verify the single-eye slipper design, spring rating and width, and compare the original measurement method, bushing, hangers and hardware. Lippert's broad competitor-fit wording does not replace a dimensional match.
What comes with this spring?
One slipper leaf spring is listed. Lippert says the eye bushing is pre-installed. Hanger kits are sold separately and suitable pre-mounted hangers are required. A pair of springs, U-bolts, spring plate, eye bolt, equalizer or complete mounting kit is not itemized as included.
Is 8,000 pounds the axle rating?
The product page calls this an 8,000-lb spring assembly capacity. Do not treat that as a complete axle or trailer rating, double it to claim a suspension rating, or use it to increase the original gross vehicle weight rating. The axle, hangers, frame, wheels, tires and full suspension must retain their approved ratings.
Why does the page say eye-to-eye when it has one eye?
Lippert's title and specification call the length 30.5 inches eye-to-eye, while the quick facts and photos show a single-eye slipper spring. Preserve 30.5 inches as the published length, but confirm the exact eye-center-to-slipper measurement convention on the original spring before purchase. It is not a two-eye spring, and a second eye is not implied.
Which cross-reference numbers apply?
Lippert lists Standens leaf spring number 72-46 and Dexter compatible part number 072-046-00 for this SKU. These are identification aids: confirm the original label, spring style, dimensions, eye/bushing size, mounting arrangement and load requirements. They do not establish compatibility with every Dexter or competitor axle.
What does the load arch specification mean here?
The source lists Load Arch Length as 2.75, without an explicit unit or measurement method in that field. Confirm the unit and whether the original spring is measured loaded or unloaded before using that figure for fit. The page does not give the bushing bore, bolt diameter, leaf thickness or exact hanger spacing.
Can I use an equalizer just because it takes a 3-inch spring?
No. Spring width alone does not establish the correct equalizer or hanger arrangement. Match axle spacing, original suspension design, spring-end geometry and hardware specifications. The related equalizers below are comparison resources with their own dimensions, not confirmed companion parts for every installation of this spring.
Where can I find installation instructions?
The page provides general support links, with no exact spring installation PDF linked. Use the trailer and suspension manufacturer instructions, including the correct support points, replacement hardware and fastener torque. Inspect and maintain the equipment periodically as Lippert directs. The page's generic DIY wording does not supply an installation procedure.
Are the shipping measurements the spring dimensions?
No. Lippert lists the package at 41 x 20 x 10 inches and 55 pounds. The separate item dimensions are 30.5 inches long and 3 inches wide. Shipping measurements do not establish installed arch, eye diameter, hanger spacing or spring clearance.
Compare Suspension Components
For research, compare the 3-inch spring-width equalizer for 42-1/4-inch axle spacing, 299015 and 3-inch spring-width equalizer for 48-1/2-inch axle spacing, 299017. Their shared spring-width designation does not establish that either fits this spring in your trailer; verify the full original suspension.
Manufacturer warning: Cancer and reproductive harm. See www.P65Warnings.ca.gov.
| Sku | 353498 |
|---|---|
| Brand | Lippert |
| Weight capacity | 8,000 lbs. |
| Standens leaf spring number | 72-46 |
| Spring layer count | 6 |
| Eye to eye length | 30.5 |
| Axle spring type | Slipper Leaf |
| Load arch length | 2.75 |
| Axle type | Spring |
| Hardware type | Spring |
| Unit of measure | EA |
| Item length (inches) | 30.5 |
| Item width (inches) | 3 |
| Warranty term | 1 Year |
| Quantity in package | 1 |
| Package type | Kraft Box |
| Country of origin | USA |
| Dexter compatible part number | 072-046-00 |
| Upc | 848150068804 |
| Shipping dimensions | 41" L x 20" W x 10" H, 55 lbs. |
- What comes with this spring? One slipper leaf spring is listed. Lippert says the eye bushing is pre-installed. Hanger kits are sold separately and suitable pre-mounted hangers are required. A pair of springs, U-bolts, spring plate, eye bolt, equalizer or complete mounting kit is not itemized as included.
- Is 8,000 pounds the axle rating? The product page calls this an 8,000-lb spring assembly capacity. Do not treat that as a complete axle or trailer rating, double it to claim a suspension rating, or use it to increase the original gross vehicle weight rating. The axle, hangers, frame, wheels, tires and full suspension must retain their approved ratings.
- Why does the page say eye-to-eye when it has one eye? Lippert's title and specification call the length 30.5 inches eye-to-eye, while the quick facts and photos show a single-eye slipper spring. Preserve 30.5 inches as the published length, but confirm the exact eye-center-to-slipper measurement convention on the original spring before purchase. It is not a two-eye spring, and a second eye is not implied.
- Which cross-reference numbers apply? Lippert lists Standens leaf spring number 72-46 and Dexter compatible part number 072-046-00 for this SKU. These are identification aids: confirm the original label, spring style, dimensions, eye/bushing size, mounting arrangement and load requirements. They do not establish compatibility with every Dexter or competitor axle.
- What does the load arch specification mean here? The source lists Load Arch Length as 2.75, without an explicit unit or measurement method in that field. Confirm the unit and whether the original spring is measured loaded or unloaded before using that figure for fit. The page does not give the bushing bore, bolt diameter, leaf thickness or exact hanger spacing.
- Can i use an equalizer just because it takes a 3-inch spring? No. Spring width alone does not establish the correct equalizer or hanger arrangement. Match axle spacing, original suspension design, spring-end geometry and hardware specifications. The related equalizers below are comparison resources with their own dimensions, not confirmed companion parts for every installation of this spring.
- Where can i find installation instructions? The page provides general support links, with no exact spring installation PDF linked. Use the trailer and suspension manufacturer instructions, including the correct support points, replacement hardware and fastener torque. Inspect and maintain the equipment periodically as Lippert directs. The page's generic DIY wording does not supply an installation procedure.
- Are the shipping measurements the spring dimensions? No. Lippert lists the package at 41 x 20 x 10 inches and 55 pounds. The separate item dimensions are 30.5 inches long and 3 inches wide. Shipping measurements do not establish installed arch, eye diameter, hanger spacing or spring clearance.
Loading customer reviews…
Factory-Fresh OEM Parts — the same brands installed in new RVs straight from Elkhart. Genuine, name-brand components made to order — never generic, never outdated. Sourced directly from the original RV manufacturers for perfect fit and factory-level quality.





