How to read MORryde cargo tray sizes

MORryde lists tray sizes a few different ways depending on the product line. That can feel confusing when you’re matching a tray to a basement door opening—or trying to see if a cooler or tote will sit between the rails.

Here’s a plain-English guide to CTG cargo trays, SP56 freezer trays, and SP60 utility trays, based on MORryde’s published charts and how these trays are built.

Quick rule: Always measure your door opening and your gear. Charts tell you the tray; your tape measure tells you the fit.


CTG cargo trays (60% extension)

How the part number works

The last four digits of a standard CTG part number are the listed width × length in inches.

Example part # Listed size
CTG60-2348W 23″ W × 48″ L
CTG60-2648W 26″ W × 48″ L
CTG60-3660W 36″ W × 60″ L

Widths commonly run 20″ through 52″; lengths commonly run 36″, 48″, 60″, 72″, and 90″ (90″ trays typically slide out from both sides of the unit).

Listed size = outer dimensions

For CTG cargo trays, the listed width and length are outer dimensions. Nothing on the tray is meant to stick out past those listed outer dims.

Confirm exact clearance before ordering

MORryde identifies the listed size as the outer dimensions. Do not subtract a universal ¼″ allowance or assume that an opening equal to the listed width guarantees installation clearance. Check the exact assembly, door hardware and mounting space.

Example: CTG60-2348W is listed as 23″ wide × 48″ long. Those dimensions do not establish a measured 22¾″ assembly width or the usable width between its rails.

Before mounting, follow the installation instructions to check that the baggage door opens and closes freely and the tray clears the opening. Use a second person for lifting and follow the instructions’ limits on extending an unsecured tray.

Under-tray clearance and compartment lip

MORryde’s current FAQ specifies 1.6″ between the underside of the tray and the compartment floor. That is not the height of the tray’s lip or its overall installed height. Measure the door-frame lip and overhead clearance for your installation. CTG54-001 risers add height; they reduce the overhead space available and do not increase the tray’s load rating.

Usable space between the rails (coolers & totes)

Unlike freezer trays, the CTG charts reviewed here do not specify a carpet-between-rails usable inside dimension (I.D.) the way they do for SP56 freezer trays.

That means:

  • The listed width is outer, not “how wide your cooler can be.”
  • Rails, carpet, and lip all eat into usable width.
  • We don’t promise a specific cooler or tote will fit without you measuring your tote’s outside width against the usable space on the tray you choose.

Best practice: Measure the outside width of your cooler/tote, then leave a little wiggle room for carpet and rails. If you’re between sizes, check both usable cargo space and the larger assembly’s installation clearance before choosing. Send the exact tray number and your measurements if you need help.

Weight capacity (published): Standard CTG60 cargo trays are listed at 800 lb capacity. Separate CTG80 dual-way 72″ trays are listed at 500 lb.


SP56 freezer trays

SP56 freezer / sliding trays are different: MORryde publishes both outside dimensions (O.D.) and inside dimensions (I.D.) on the chart.

That makes cooler and freezer planning much clearer—you can compare your appliance’s footprint to the I.D., and compare the opening/bay to the O.D.

Current manufacturer dimensions

Part # Style O.D. (W × D × H) I.D. (W × D × H)
SP56-115 Front pull 37.6″ × 21.6″ × 5″ 31.42″ × 19.7″ × 2.5″
SP56-132 Side pull 18″ × 26.5″ × 6″ 14″ × 24.8″ × 2.5″

The older Sliding Tray Flyer lists SP56-203 as a hidden tray, 26.3″ W × 16.1″ L × 2.7″ H, for framing spacing 20″–26″. Current specialty-tray literature instead identifies SP56-203H. Preserve the complete suffix when checking dimensions and mounting; these references alone do not prove the two versions interchangeable.

The current freezer-tray page and specialty chart give the SP56-115 and SP56-132 dimensions above, 200% extension and 225 lb capacity. The older flyer gives different 3.5″ heights; do not use it as the current height specification. Hidden trays are a separate style: check their exact suffix, extension and rating rather than transferring the freezer-tray specification.


SP60 utility trays

For SP60 utility trays, the dimensions on the chart are inside dimensions.

The older flyer says to add 2″ to width and depth, but current specialty-tray literature supplies exact outside dimensions. Use the exact row for the part number instead of that blanket conversion.

Example (inside, listed) Current outside dimensions (W × D × H)
SP60-041 — 14″ × 14″ × 2.75″ 16.25″ × 15.75″ × 5″
SP60-044 — 24″ × 24″ × 2.75″ 26.25″ × 25.75″ × 5″

SP60-041 is rated at 250 lb; SP60-044 is rated at 300 lb. Other utility-tray models have different ratings. Check the exact model and mounting limits.


CTG vs SP56 vs SP60 — at a glance

Family What the listed size means Published I.D.? Best for
CTG cargo trays Outer W × L (from part #) No between-rails I.D. in the CTG charts reviewed Basement cargo, totes, generators, general gear
SP56 freezer trays Chart shows O.D. and I.D. Yes Freezers / fridges / cargo you need past the slideout
SP60 utility trays Chart shows inside and outside dimensions by exact part number Inside is what’s listed Generators, LP tanks, compact utility storage

How to measure before you buy

  1. Door / bay opening — Measure the clear width and depth of the compartment opening (and watch for hinges, gas struts, and door seals).
  2. Tray listed size — Compare CTG listed outer size with the available installation space; confirm actual assembly and clearance without subtracting a universal allowance.
  3. Your gear — Measure the outside of coolers, totes, freezers, or tanks.
  4. Usable space — For SP56, use the published I.D. For CTG, don’t assume listed width equals tote width—leave margin for rails and carpet.
  5. Lip / risers — If your compartment has a tall lip, look at the cargo tray riser kit options so the tray clears when extended.

Still unsure? Send us your door-opening width and the outside width of what you want to carry. We’re happy to help you pick a size—without guessing.


Charts & install guides

Use the document that matches the exact part and revision. Hosted copies remain useful references, but older dimensions can differ from current manufacturer specifications. The hosted cargo chart matches the current manufacturer cargo chart checked for this review; the Sliding Tray Flyer is a legacy reference.

Document What it’s for ERVP-hosted reference Manufacturer source
Sliding-Tray-Flyer.pdf Legacy OD/ID charts for SP56; SP60 inside-dim note; CTG overview Download (ERVP-hosted) Current specialty-tray dimensions
cargo-trays.pdf CTG cargo tray size chart (23″ widths, riser kit, CTG80) Download (ERVP-hosted) Manufacturer cargo chart
Cargo-Tray-Installation.pdf Install steps, door-clearance check, hardware notes Download (ERVP-hosted) Manufacturer cargo-tray FAQ

Shop MORryde trays at Extreme RV Parts


Sizing notes distinguish current MORryde dimensions from legacy chart references. Specs can vary by part number—always confirm on the product page and measure your coach and gear before ordering.