MORryde TV10-S-35H Swivel Snap-In TV Mount - 35 lb
Ready to order
MORryde TV10-S-35H Swivel Snap-In TV Mount - 35 lb
---
Match the swivel mount, exact TV holes and wall support
TV10-S-35H is a swivel snap-in mount for a flat-panel TV or monitor on a vertical RV mounting surface, with a 35 lb maximum TV weight. The TV-side plate stays attached to the television when it is detached from the wall plate. This model provides swivel adjustment; no exact swivel angle, tilt range or extension travel is established by the reviewed instructions.
The current TV10-S-35H version 2 manual lists 75 x 75, 100 x 100, 100 x 200 and 200 x 200 mm VESA patterns. MORryde’s product page instead lists 100 x 150 mm alongside the other three sizes. The 100 x 150 and 100 x 200 mm statements differ; do not treat them as interchangeable or assume all patterns below 200 x 200 fit. Verify the supplied TV-side plate, horizontal and vertical hole spacing, and the correct manufacturer instructions for your revision before ordering.
The current manual requires a vertical mounting surface able to support five times the combined weight of the TV and mount; reinforcement may be necessary. It excludes brick, concrete and concrete block. An RV wall covering alone does not establish structural support. Verify the mounting structure, TV recesses, cable and connector access, and swivel/removal clearance before installation.
The current version 2 manual identifies a portable mounting plate, TV bracket and hardware pack, and illustrates M4, M5 and M6 x 12 mm TV bolts, washers and separate 1/4-inch lag bolts for the wall plate. The retained earlier manual shows additional bolt lengths, M8 options, spacers and different bracket-fastener guidance. Match the actual supplied revision and the television owner’s specified thread and insertion depth. Do not mix hardware packs or assume every illustrated option is supplied or needed. Hardware that is too long can puncture exterior structures.
Use the exact TV10-S-35H bracket and wall-plate engagement shown in its instructions. The reviewed documents do not establish a separate replacement-plate or hardware-pack part number, cross-model latch interchangeability, an exact adapter pairing, or fit to a named television model. The existing Extension Arm and Rigid selector choices are different complete mounts. A shared snap-in name, 35 lb rating or VESA pattern does not certify that their plates interchange. Confirm secure attachment and the appropriate travel procedure for the actual assembly; the reviewed manual does not specify a separate travel-lock procedure.
MORryde’s current product page gives overall assembled dimensions of 8.5 in high x 9.8 in wide x 3.38 in deep. Retained catalog length, width/height, physical or shipping weight and dimensional-weight entries from other records are unverified references, not certified net assembly or packed dimensions. They do not establish the clearance needed to swivel or remove the television.
Exact manufacturer specifications · Current TV10-S-35H instructions (version 2)
MORryde RV TV mount TV10-S-35H is for RV owners, mobile techs, and dealers who need to match a MORryde component by the real SKU instead of guessing from a generic photo. Use this listing to confirm part TV10-S-35H, review the visible specs, and choose the correct replacement or upgrade for the job.
This product solves the common RV-parts problem of finding the exact MORryde item without mixing it up with a similar-looking step, tray, suspension, pin-box, TV-mount, or accessory part. The trade-off is fitment: MORryde parts are often size-, rating-, side-, generation-, or application-specific, so confirm your original label, measurement, or documentation before ordering.
Original product note: Snap-In TV Mount Quickly disconnect your TV from its docking station with this snap-in wall TV mount for your RV. No need to unscrew the TV or monitor from the VESA plate. A swivel feature positions your TV for ideal viewing. FEATURES: Patented snap-in design Detachable TV plate 35 lb. weight capacity IN THE BOX: TV mounting plate Wall mount plate Installation hardware Installation instructions Skip the hassle of unscrewing the TV from the VESA plate with this snap-in TV mount. The patented design makes it easy to …
Features & Specifications
- Brand: MORryde
- SKU: TV10-S-35H
- Part Number: TV10-S-35H
- Product Family: MORryde RV TV Mounts
- Capacity: 35 lbs
- Shipping Weight: 10 lb
- Product Type: RV TV Mounts
- Application: mounting or securing an RV TV after matching VESA pattern, weight rating, and mount style
Why Choose TV10-S-35H?
This MORryde listing is built around part-number accuracy, practical RV use, and clear comparison against nearby options in the ERVP catalog. That matters because a similar title or product image does not guarantee the same dimensions, rating, attachment side, slide direction, or system generation.
Fitment limit: match this item to your existing MORryde part number, RV measurement, TV weight, VESA hole spacing, mounting footprint, or MORryde documentation. If the verified details do not match your RV, choose the correct sibling or alternative instead of forcing this part.
Compare MORryde RV TV Mounts
Not sure which MORryde option is right? Compare this product with nearby ERVP listings and verify the part number before ordering.
| Model / Part | Category | Best For | View Details |
|---|---|---|---|
|
TV10-S-35H Snap-In TV Mount - 35 lb. capacity - TV10-S-35H |
RV TV Mounts | mounting or securing an RV TV after matching VESA pattern, weight rating, and mount style | Current Product |
| TV1-051H Snap-In TV Mount - 25 lb. capacity - TV1-051H |
RV TV Mounts | Different complete mount; verify its own motion, VESA pattern, weight and footprint. No interchangeable latch plate is established. | View Details |
| TV1-048H Snap-In TV Mount - 35 lb. capacity - TV1-048H |
RV TV Mounts | Different complete mount; verify its own motion, VESA pattern, weight and footprint. No interchangeable latch plate is established. | View Details |
| TV56-129H Drop Down TV Mount - 20 lb. capacity - TV56-129H |
RV TV Mounts | Different complete mount; verify its own motion, VESA pattern, weight and footprint. No interchangeable latch plate is established. | View Details |
Tip: MORryde part numbers are specific. Check the SKU and the physical measurement, rating, side, generation, or application on your RV before choosing between similar listings.
Technical Specifications
| Brand | MORryde |
| SKU | TV10-S-35H |
| Part Number | TV10-S-35H |
| Product Family | MORryde RV TV Mounts |
| Capacity | 35 lbs |
| Shipping Weight | 10 lb |
| Product Type | RV TV Mounts |
What's Included
Includes the MORryde product listed as part number TV10-S-35H. It does not include unrelated hardware, brackets, companion parts, or a complete system unless those items are specifically named in the product title or description.
Compatible Models & Alternatives
Use the comparison table above for nearby MORryde options. Choose related parts by confirmed part number, size, capacity, width, side, system generation, VESA pattern, frame type, or documented MORryde application. chip_label, sibling_products, dimension_config, current_dimensions
Frequently Asked Questions
- How do I confirm this is the right MORryde part?
- TV10-S-35H is a swivel snap-in mount for a flat-panel TV or monitor on a vertical RV mounting surface, with a 35 lb maximum TV weight. The TV-side plate stays attached to the television when it is detached from the wall plate. This model provides swivel adjustment; no exact swivel angle, tilt range or extension travel is established by the reviewed instructions. The current TV10-S-35H version 2 manual lists 75 x 75, 100 x 100, 100 x 200 and 200 x 200 mm VESA patterns. MORryde’s product page instead lists 100 x 150 mm alongside the other three sizes. The 100 x 150 and 100 x 200 mm statements differ; do not treat them as interchangeable or assume all patterns below 200 x 200 fit. Verify the supplied TV-side plate, horizontal and vertical hole spacing, and the correct manufacturer instructions for your revision before ordering.
- What should I measure before ordering?
- MORryde’s current product page gives overall assembled dimensions of 8.5 in high x 9.8 in wide x 3.38 in deep. Retained catalog length, width/height, physical or shipping weight and dimensional-weight entries from other records are unverified references, not certified net assembly or packed dimensions. They do not establish the clearance needed to swivel or remove the television. The current manual requires a vertical mounting surface able to support five times the combined weight of the TV and mount; reinforcement may be necessary. It excludes brick, concrete and concrete block. An RV wall covering alone does not establish structural support. Verify the mounting structure, TV recesses, cable and connector access, and swivel/removal clearance before installation.
- Can I substitute a similar MORryde product?
- Use the exact TV10-S-35H bracket and wall-plate engagement shown in its instructions. The reviewed documents do not establish a separate replacement-plate or hardware-pack part number, cross-model latch interchangeability, an exact adapter pairing, or fit to a named television model. The existing Extension Arm and Rigid selector choices are different complete mounts. A shared snap-in name, 35 lb rating or VESA pattern does not certify that their plates interchange. Confirm secure attachment and the appropriate travel procedure for the actual assembly; the reviewed manual does not specify a separate travel-lock procedure.
- What do buyers usually pair with this part?
- The current version 2 manual identifies a portable mounting plate, TV bracket and hardware pack, and illustrates M4, M5 and M6 x 12 mm TV bolts, washers and separate 1/4-inch lag bolts for the wall plate. The retained earlier manual shows additional bolt lengths, M8 options, spacers and different bracket-fastener guidance. Match the actual supplied revision and the television owner’s specified thread and insertion depth. Do not mix hardware packs or assume every illustrated option is supplied or needed. Hardware that is too long can puncture exterior structures. Use the exact TV10-S-35H bracket and wall-plate engagement shown in its instructions. The reviewed documents do not establish a separate replacement-plate or hardware-pack part number, cross-model latch interchangeability, an exact adapter pairing, or fit to a named television model. The existing Extension Arm and Rigid selector choices are different complete mounts. A shared snap-in name, 35 lb rating or VESA pattern does not certify that their plates interchange. Confirm secure attachment and the appropriate travel procedure for the actual assembly; the reviewed manual does not specify a separate travel-lock procedure.
Why Buy from Elkhart RV Parts?
Elkhart RV Parts focuses on hard-to-find RV service parts with clear part-number identification, practical fitment notes, and fast support from a team located in Elkhart, Indiana.
| Depth (inches) | 3.38 |
|---|---|
| Width (inches) | 7 |
| Height (inches) | 10 |
| Length (inches) | 14 |
| Physical weight (pounds) | 10 |
| Weight capacity (pounds) | 35 |
| Dimensional weight (pounds) | 9 |
| Vesa mounting pattern 1 (millimeters) | 75x75 |
| Vesa mounting pattern 2 (millimeters) | 100x100 |
| Vesa mounting pattern 3 (millimeters) | 100x150 on product page / 100x200 in version 2 manual; verify actual plate and revision |
| Vesa mounting pattern 4 (millimeters) | 200x200 |
| Exact manufacturer model | TV10-S-35H |
| Mount movement | TV10-S-35H is a swivel snap-in mount for a flat-panel TV or monitor on a vertical RV mounting surface, with a 35 lb maximum TV weight. The TV-side plate stays attached to the television when it is detached from the wall plate. This model provides swivel adjustment; no exact swivel angle, tilt range or extension travel is established by the reviewed instructions. |
| Vesa source and revision distinction | The current TV10-S-35H version 2 manual lists 75 x 75, 100 x 100, 100 x 200 and 200 x 200 mm VESA patterns. MORryde’s product page instead lists 100 x 150 mm alongside the other three sizes. The 100 x 150 and 100 x 200 mm statements differ; do not treat them as interchangeable or assume all patterns below 200 x 200 fit. Verify the supplied TV-side plate, horizontal and vertical hole spacing, and the correct manufacturer instructions for your revision before ordering. |
| Mounting surface requirements | The current manual requires a vertical mounting surface able to support five times the combined weight of the TV and mount; reinforcement may be necessary. It excludes brick, concrete and concrete block. An RV wall covering alone does not establish structural support. Verify the mounting structure, TV recesses, cable and connector access, and swivel/removal clearance before installation. |
| Hardware pack revision | The current version 2 manual identifies a portable mounting plate, TV bracket and hardware pack, and illustrates M4, M5 and M6 x 12 mm TV bolts, washers and separate 1/4-inch lag bolts for the wall plate. The retained earlier manual shows additional bolt lengths, M8 options, spacers and different bracket-fastener guidance. Match the actual supplied revision and the television owner’s specified thread and insertion depth. Do not mix hardware packs or assume every illustrated option is supplied or needed. Hardware that is too long can puncture exterior structures. |
| Plate interchangeability and travel | Use the exact TV10-S-35H bracket and wall-plate engagement shown in its instructions. The reviewed documents do not establish a separate replacement-plate or hardware-pack part number, cross-model latch interchangeability, an exact adapter pairing, or fit to a named television model. The existing Extension Arm and Rigid selector choices are different complete mounts. A shared snap-in name, 35 lb rating or VESA pattern does not certify that their plates interchange. Confirm secure attachment and the appropriate travel procedure for the actual assembly; the reviewed manual does not specify a separate travel-lock procedure. |
| Manufacturer overall assembly dimensions | 8.5 in H x 9.8 in W x 3.38 in D |
| Other catalog measurements | MORryde’s current product page gives overall assembled dimensions of 8.5 in high x 9.8 in wide x 3.38 in deep. Retained catalog length, width/height, physical or shipping weight and dimensional-weight entries from other records are unverified references, not certified net assembly or packed dimensions. They do not establish the clearance needed to swivel or remove the television. |
- What is the weight capacity of the morryde tv10-s-35h snap-in tv mount? TV10-S-35H is a swivel snap-in mount for a flat-panel TV or monitor on a vertical RV mounting surface, with a 35 lb maximum TV weight. The TV-side plate stays attached to the television when it is detached from the wall plate. This model provides swivel adjustment; no exact swivel angle, tilt range or extension travel is established by the reviewed instructions.
- Does this tv mount allow for swiveling the tv for better viewing angles? TV10-S-35H is a swivel snap-in mount for a flat-panel TV or monitor on a vertical RV mounting surface, with a 35 lb maximum TV weight. The TV-side plate stays attached to the television when it is detached from the wall plate. This model provides swivel adjustment; no exact swivel angle, tilt range or extension travel is established by the reviewed instructions.
- What vesa mounting patterns are compatible with this tv mount? The current TV10-S-35H version 2 manual lists 75 x 75, 100 x 100, 100 x 200 and 200 x 200 mm VESA patterns. MORryde’s product page instead lists 100 x 150 mm alongside the other three sizes. The 100 x 150 and 100 x 200 mm statements differ; do not treat them as interchangeable or assume all patterns below 200 x 200 fit. Verify the supplied TV-side plate, horizontal and vertical hole spacing, and the correct manufacturer instructions for your revision before ordering.
- Is it necessary to unscrew the tv from the vesa plate to remove it from the mount? TV10-S-35H is a swivel snap-in mount for a flat-panel TV or monitor on a vertical RV mounting surface, with a 35 lb maximum TV weight. The TV-side plate stays attached to the television when it is detached from the wall plate. This model provides swivel adjustment; no exact swivel angle, tilt range or extension travel is established by the reviewed instructions. Use the exact TV10-S-35H bracket and wall-plate engagement shown in its instructions. The reviewed documents do not establish a separate replacement-plate or hardware-pack part number, cross-model latch interchangeability, an exact adapter pairing, or fit to a named television model. The existing Extension Arm and Rigid selector choices are different complete mounts. A shared snap-in name, 35 lb rating or VESA pattern does not certify that their plates interchange. Confirm secure attachment and the appropriate travel procedure for the actual assembly; the reviewed manual does not specify a separate travel-lock procedure.
- What items are included in the box with the morryde tv10-s-35h snap-in tv mount? The current version 2 manual identifies a portable mounting plate, TV bracket and hardware pack, and illustrates M4, M5 and M6 x 12 mm TV bolts, washers and separate 1/4-inch lag bolts for the wall plate. The retained earlier manual shows additional bolt lengths, M8 options, spacers and different bracket-fastener guidance. Match the actual supplied revision and the television owner’s specified thread and insertion depth. Do not mix hardware packs or assume every illustrated option is supplied or needed. Hardware that is too long can puncture exterior structures.
- What wall support and installation checks are required? The current manual requires a vertical mounting surface able to support five times the combined weight of the TV and mount; reinforcement may be necessary. It excludes brick, concrete and concrete block. An RV wall covering alone does not establish structural support. Verify the mounting structure, TV recesses, cable and connector access, and swivel/removal clearance before installation. The current version 2 manual identifies a portable mounting plate, TV bracket and hardware pack, and illustrates M4, M5 and M6 x 12 mm TV bolts, washers and separate 1/4-inch lag bolts for the wall plate. The retained earlier manual shows additional bolt lengths, M8 options, spacers and different bracket-fastener guidance. Match the actual supplied revision and the television owner’s specified thread and insertion depth. Do not mix hardware packs or assume every illustrated option is supplied or needed. Hardware that is too long can puncture exterior structures.
- Can i use a plate or adapter from another snap-in mount? Use the exact TV10-S-35H bracket and wall-plate engagement shown in its instructions. The reviewed documents do not establish a separate replacement-plate or hardware-pack part number, cross-model latch interchangeability, an exact adapter pairing, or fit to a named television model. The existing Extension Arm and Rigid selector choices are different complete mounts. A shared snap-in name, 35 lb rating or VESA pattern does not certify that their plates interchange. Confirm secure attachment and the appropriate travel procedure for the actual assembly; the reviewed manual does not specify a separate travel-lock procedure.
Loading customer reviews…
Factory-Fresh OEM Parts — the same brands installed in new RVs straight from Elkhart. Genuine, name-brand components made to order — never generic, never outdated. Sourced directly from the original RV manufacturers for perfect fit and factory-level quality.








