Universal Fresh Water Tank Fittings Kit w/ Water Level Sensors for RV

Elkhart RV PartsSKU: ERVP-FRESHTANKKIT
No reviews

Price:
Sale price$34.95
Stock:
In stock (4 units), ready to be shipped

Description

If you're already purchasing an RV water tank from us, chances are you will need the fittings installed specific to your application.  This kit contains the fittings you need to fit standard PVC piping (same diameter) and customize tank to your needs.

ElkhartRVParts.com Fresh Water Fitting Kit Installation PDF Click Here

 Here is what is included in the kit:

  • 6 x - Mini probe/sensor tank inserts which require a 3/8" drill bit
  • 2 x - 1/2" grommets U50W - requires 1 1/4" hole saw.  These grommets may be white or black, but are functionally the same.
  • 2 x - 3/4" grommets U100W - requires 1 1/4" hole saw.  These grommets may be white or black, but are functionally the same.
  • 2 x - 1" grommets U075W - requires 1 3/4" hole saw.  These grommets may be white or black, but are functionally the same.
  • 2 x - 1 1/2" grommets U150W - requires 2 1/2" hole saw.  These grommets may be white or black, but are functionally the same.
  • 1 x - 2" grommet U200W - requires 3" hole saw.  These grommets may be white or black, but are functionally the same.

 Here is what you will need (not included in the kit):

  • 1-1/4" hole saw (needed for 1/2" & 3/4" grommets)
  • 1-3/4" hole saw (needed for 1" grommets)
  • 2-1/2" hole saw (needed for 1-1/2" grommets)
  • 3" hole saw (needed for 2" grommets)
  • 3/8" drill bit (needed to install the probes/sensors)
  • drill (electric or cordless)
  • safety goggles
  • tape measure
  • deburring tool (knife or rough sand paper will work too)
******************************************************************************************

Steps to install grommets:  Note that your pipe size will determine which size grommets you will need to install.

1) Mark the tank exactly where you want to place the grommets (double check your measurements to prevent an error)

2) Make a starter hole for your hole saw

3) Then cut your tank hole with the hole saw

4) Deburr the hole (important to create a tight seal)

5) Push short end of grommet with your hand into the hole till flush (check all sides to make sure seated smoothly

Steps to install sensors in standard formation.  Sensors are used to measure water level.  (please check w/tank manufacturer if unsure of where sensors should be placed)  Note:  Keep sensors at least a fingers-width from edges so probes/sensors seal properly).  Sensors are easy to install and are helpful to keep track of your tank levels.

1) Mark the tank exactly where you want to place your probes at end of tank (double          check your measurements to prevent an error). 

    a) Probes/sensors are typically placed at the end of the tank at top center (to                      measure when tank is full)

    b) Next probe is placed at the middle end of tank between the middle and side of              the tank (to measure when the tank is half-way full)

    c) The next probe is placed at the bottom towards the right corner (to measure when          the tank is empty)

   d) The last probe is placed at the bottom towards the center (to measure again when          the tank is empty)

2)  Now drill the 4 holes for the probes using your 3/8" drill bit.  Remove any burrs to           get a tight seal

3)  Push probe sensor into the hole, wiggling into place then twist nut to tighten

*******************************************************************************************

If you don't want this DIY project, we can install the fittings for you!

See our custom installation options here>

100% Authentic OEM-Quality Parts: These rotational molded fresh water tanks are crafted to meet or exceed factory standards, making them a perfect upgrade or replacement for your RV, horse trailer, or marine vessel.

Premium FDA-Approved Material: Made from high-quality, durable polyethylene that’s fully approved for safe drinking water storage—better than many stock tanks installed in factory-built RVs.

Seamless One-Piece Construction: Engineered without seams or joints for superior strength and leak-proof reliability, outlasting and outperforming typical OEM tanks.

Stain, Corrosion, and Rust Resistant: Designed to stay clean and functional even after years of use, ensuring your water stays fresh and your tank stays dependable.

Versatile Compatibility: Ideal for RV enthusiasts, horse trailer owners, or marine adventurers looking for a long-lasting, hassle-free water storage solution.

Enhanced Durability: Built tougher than many standard factory-installed tanks, offering peace of mind whether you’re replacing an old tank or upgrading your setup.

You may also like

Recently viewed